|
This CCNA™ Network Visualizer® 6.0 update is packaged into an install program. It is an accumulation of all issues noted on this page. The size of this install program is about 24 megabytes. After downloading the install file, double-click on the file and install the contents into your current CCNA™ Network Visualizer® 6.0 directory. Make sure your program is closed before running this install. You do not need to remove your license before applying an update.
November '09 Update (build 6.0.21) Fixed issue with spanning-tree where it was erratic and sometimes would not move out of the blocking state September '09 Update (build 6.0.20) Fixed issues with some practice scenario, network layouts and answers March '09 Update (build 6.0.19) Fixed issue with grading Practice Scenario VLANs and Interswitch Communications --> Configure VT March '09 Update (build 6.0.18) Fixed issue where certain configs were not saved in the rsm file and therefore not available when the file is reloaded March '09 Update (build 6.0.17) Fixed issue where Net Config was not updating correctly Fixed a pinging issue between hosts connected to the 1900 switch Fixed issue where the cable color was not correct when connecting some devices February '09 Update (build 6.0.16) Fixed issue in Lab 5.7 where routes would not show up after network was fully configured (they would show up if you saved and reloaded the network) Fixed issue where the ip address of the Vlan 1 interface on a 3560 Switch would not save Fixed issue where routes from sub interfaces would not display in the "show ip route" command Fixed issue on how OSPF routes are advertised Fixed issue where inter-vlan routing was not working as expected Corrected miscellaneous lab text February '09 Update (build 6.0.15) Fixed EIGRP no auto-summary issue in Lab 15-4 When pinging from a host, net detective displayed an incorrect ip address December '08 Update (build 6.0.15) Corrected issue with IP configuration on the 3560 Switch not working December '08 Update (build 6.0.14) Corrected issue with launching SDM Corrected text in lab 5.1 October '08 Update (build 6.0.13) Added missing labs Corrected text with VLSM labs October '08 Update (build 6.0.12) Corrected miscellaneous text related to ospf and bdr elections labs September '08 Update (build 6.0.11) Fixed issue in Lab 5.2 Step # 3 where the SDM would not launch Corrected miscellaneous text August '08 Update (build 6.0.10) Corrected miscellaneous text August '08 Update (build 6.0.9) Corrected miscellaneous text July '08 Update (build 6.0.8) Fixed issue show ip eigrp neighbors command Corrected miscellaneous text July '08 Update (build 6.0.7) Fixed issue with starting the console for a Host from the View menu on the Network Visualizer screen Fixed issue with grading EIGRP networks Fixed issue with "show vlan" on the 1900 switch Fixed help output for "vtp domain" on the 1900 switch Corrected miscellaneous text Fixed practice scenario network file for NAT and ACLs July '08 Update (build 6.0.6) Fixed Lab 6.1 (password recovery) so that ctrl-break will bring up rom monitor mode Corrected miscellaneous text June '08 Update (build 6.0.5) Fixed issue where static routes could not be removed June '08 Update (build 6.0.4) Corrected miscellaneous text June '08 Update (build 6.0.3) Added RIP IPv6 labs Added Static IPv6 labs Added Individual IPv6 labs Added IPv6 Practice Scenarios Corrected miscellaneous text Fixed issue where excluded VLANs do not pass traffic Fixed "show running-config" command to properly display "switchport trunk encapsulation dot1q" on the 3550 Switch and the 3560 Switch Fixed issue with saving and reloading network that have EIGRP configured March '08 Update (build 6.0.2) Removed practice scenario on dhcp Corrected text in lab 5.11 Corrected text in lab 7.6 January '08 Update (build 6.0.1) Fixed grading issue in the Basic Cisco Router Operations -Configure Static or Default Routes practice scenario Fixed the show startup-config command for the 2960 Switch and the 3560 Switch Fixed issue where routes were being advertised incorrectly for all protocols Fixed show ip ospf neighbor command to display the correct
interfaces and address |
